kettrecon

Shears
KD-200-R $124.95 or 6 for $119.95 These double-cut shears feed quickly and quietly, without warping or bending your finished piece (distortion is in the waste strip). It easily follows a scribed line - edges are not hardened or burred, so you get maximum use of a sheet. The swiping action of blades seals the edge of coated metals. These shears cut sheet metal up to 18 gauge in straight or contour lines at 180 inches per minute and plastic or Formica up to 3/32" thick.
KD-442-R $139.00 Vari-Speed The KD-442 variable speed shear easily cuts through 16 gauge mild steel and stainless to 18 gauge. The steel shear head has close cutting heavy duty blades that quickly cut through sheet metal, spiral pipe, metal doors and metal studs. Double cutting action provides maximum sheet usage without burring or buckling the material. At less than 5 pounds this KETT shear is both portable for location usage and durable for daily shop operations.
KD-440-R $159.00 Vari-Speed his lightweight, pistol-grip shear cuts 14 gauge mild steel and most grades of stainless to 18 gauge. Double-insulated, the 5 AMP KD-440 cuts at over 150 inches per minute, leaving a clean, flat sheet, ready to fabricate. Distortions are absorbed in an easily disposed of waste curl, leaving the sheet cool and free of burn, chips and burrs. The cutting blades are finest high-speed steel, which you can easily replace.

Fiber Cement Shears
KC-193-R $169.95 The KC-193 variable speed 5.5 amp model comes with the heavy duty steel cutting head to provide fast cutting of up to 1/2" backer board or fiber-cement board with no airborne dust and minimal clean-up. The long lasting A-2 tool steel blades last longer and cut cleaner than expensive carbide tipped saw blades
KC-292-R $ 149.95 The KD-292 single speed 5 amp model comes with an aluminum cutting head to provide fast cutting of up to 1/2" backer board or fiber-cement board with no airborne dust and minimal clean-up. The long lasting A-2 tool steel blades last longer and cut cleaner than expensive carbide tipped saw blades.
Scissor Shear
KC-141-R $149.00 With speeds up to 2500 strokes per minute, the 5 pound KD-441 quickly cuts through plastics, wire mesh and rubber with a clean scissors action. When cutting thin coated metals, the swiping cut seals edges and is less likely to rust or corrode. This 5 AMP scissor shear is ideal when cutting through steel siding's multi-thickness nailing strip and continuing across the sheet and through the lip.

KD-441 $179.95 With speeds up to 2500 strokes per minute, the 5 pound KD-441 quickly cuts through plastics, wire mesh and rubber with a clean scissors action. When cutting thin coated metals, the swiping cut seals edges and is less likely to rust or corrode. This 5 AMP scissor shear is ideal when cutting through steel siding's multi-thickness nailing strip and continuing across the sheet and through the lip. Shear blades 41-21 center blade 41-22 stationary side knife 70-05 spacer

Air Scissor Shear
P-541-R $79.00 $10.00 OFF OR FREE FREIGHT. TILL THEIR GONE BUY AS MANY AS YOU WANT. The KETT heavy-duty scissor shear has been specially designed for fast, accurate cutting of steel siding. You'll discover it also handles other hard to cut metal, plastic and rubber sheet materials without fouling or stalling. The unique swiping action of the scissor blades leaves a clean, sheared edge. the power unit, with variable speeds from 0 to 2200 RPM, is ideal when cutting through steel siding's multi-thickness nailing strip and continuing across the sheet and difficult angle cuts following a scribed line. The P-541 will cut wire mesh up to 18 gauge, soft plastic or rubber to 1/4" and rigid PVC and other plastics to 1/8" thick with power to spare. The 5 pound P-541 delivers 2200 RPM when driven by a 90 PSI air power source.
Air Shear
P-1060-R $79.00 $10.00 OFF OR FREE FREIGHT. TILL THEIR GONE. BUY AS MANY AS YOU WANT. The P-1060 Straight Handle Pneumatic Shear features a variable speed push lever control which provides a smooth, well balanced grip. This double-cut shear easily cuts through 18 gauge mild steel and stainless to 20 gauge, eliminating the need to file or deburr. The P-1060 delivers up to 2500 RPM's when powered by a 90 PSI air source.
P-500-R $79.00 $10.00 OFF OR FREE FREIGHT. TILL THEIR GONE. BUY AS MANY AS YOU WANT. The double-cutting action of the P-500, cleanly cuts 18 gauge and lighter sheet metal without distortion. The 7/32" waste curl leaves both sides of the cut straight with no need to file or de-burr. Variable speed trigger lets you control speed from 0 to 180 inches per minute. The P-500 delivers up to 2200 RPM's when powered by a 90 PSI air power source. Ideal for the tinner, roofer and auto body shop.
P-542-R $79.00 $10.00 OFF OR FREE FREIGHT. TILL THEIR GONE. BUY AS MANY AS YOU WANT. A variable speed trigger allows smooth, easy starting cuts in mild steel to 16 gauge and most grades of stainless to 18 gauge. The 7/32" waste curl leaves both sides of the cut straight, with no need to file or de-burr. At 3 1/2 pounds and 11" long the P-542 is lightweight and portable. It features the KETT 2200 rpm power unit designed for maximum efficiency at 90 PSI air pressure.
P-540-R $79.00 $10.00 OFF OR FREE FRIGHT. TILL THEIR GONE. BUY AS MANY AS YOU WANT. The P-540 takes over where the P-500 leaves off, cutting up to 14 gauge in cold rolled steel. Its variable-speed trigger lets you make smooth, easy starting cuts even in most grades of stainless up to 16 gauge. The 4 pound, pistol grip, 2200 RPM pneumatic motor, runs on a 90 PSI power source. A great time-saver in any construction company, sheet metal or sign shop.

Return